TEXSEAL   “TexSeal” gaskets are made with a special O-Ring sealing element inlayed in the face of the gasket. This O-Ring creates a very flexible seal that requires less bolt or stud torque to maintain constant contact with the flanges sealing surface surface. TexSeal gaskets are available in both F and E styles. The O-Ring seal and gasket are available in a wide variety of materials. Type D gaskets are machined from a specified insulating material and are designed to fit ring joint type groove flanges. BX gaskets are also available. Available Materials: Hi-Temp G-3, G-7, G-10, G11, Phenolic A 1/4” thick closed cell neoprene sponge flange protector is recommended to prevent the flanges from shorting out. Type E gaskets offer complete protection for both flange faces. The gasket centers easily having the same outside diameter as the flange. This prevents foreign matter from accumulating between flange faces and shorting out the flanges Type E-RTJ combination gaskets are are made with an insulating ring joint gasket and insulating inner and outer rings. This special design gasket offers complete protection for both flange faces. The RTJ gasket provides the seal, while the 1/32'' thick inner and outer barrier rings cover the I.D. to the O.D. This prevents foreign matter from accumulating between flange faces and shorting out the flanges. It is available in most sizes and materials Type F gaskets are fabricated to fit the raised face portion of the flange face and are designed to center on the inside of the bolt circle. We recommend that a flange protector made from 1/4” thick closed cell neoprene sponge be used to prevent foreign matter from collecting between the flange faces. Selections               TexSeal                           Full Face                  Raised Face                        RTJ     Sealing NS Nitrile TS Teflon VS Viton GS Graphite QS Non-Asb     Gasket G10 G-10 Epoxy/Glass G11 G-11 Epoxy/Glass HTG-3 High Temp N Nitrile Coated Phenolic P Phenolic Q Non-Asbestos R Red Rubber RD JM 940 (Red Devil)     Washers SW Single Washer DW Double Washer Phenolic and Plated Steel Washers are standard Other materials available on request are... G10 G11 HTG-3 (Hi-Temp 450°F) TexMica (Hi-Temp 932°F)     Sleeves G10 G11 Integral (Minlon) JM 940 (Red Devil) Mylar Nomex Phenolic (Micarta) Polyethylene (Poly) Teflon read more

Sling Material UV Resistant Threaded Polyester Model Size Sling Model Material HB125ED For 1” Hose Metal “D-Ring” Sling Urethane HB200SRD For 2” Hose Metal “D-Ring” Sling Urethane HB300D For 3” Hose Metal “D-Ring” Sling Urethane HB400D For 4” Hose Metal “D-Ring” Sling Urethane HB600H For 6” Hose Type 4 Hook Eye Urethane HB800H For 8” Hose Type 4 Hook Eye Urethane HB1000H For 10” Hose Type 4 Hook Eye Urethane   read more

Hose Diameter Internal (ID) Width Around Hose (mm) Length Along Hose (mm) Nett Buoyancy Weight (Kgs) 2”   (50mm) 440 600 8 / 9 3”   (75mm) 512 600 12    4”  (100mm) 720 600 17    5”   (125mm) 812 750 28    6”   (150mm) 1000 750 32 read more

The TODO® Safety Pressure Tight Cap was designed in cooperation with the major European chemical companies and other interested parties. The aim was to design a sealing cap system that would reduce pressure behind the cap if all other upstream closures had failed, thus protecting the operator from harm. The cap system also alerts the operator to the existence of pressure behind the cap thus giving warning of potential upstream valve failure. The TODO® Safety Pressure Tight Cap is certified as a full first or primary closure when used in combination with TODO-MATIC® or TODO-GAS® couplings. The cap can also be custom sealed to prevent unauthorised operation. There simply is no other coupling and cap system available with such a high level of passive safety features. Specifications Dimensions 2" - 4" DN 50 - DN 100 Materials 316L Stainless Steel Seals A full range of elastomeric seals available read more